In some cases, your system may generate a message stating that a hyper-Transport sync error occurred during the last boot. There can be several reasons for this problem.
The “Hyper Transport Sync Flood Error” occurs during the “Immediately On First Boot” screen only after the user boots up the PC. After that, the boot sequence completes by setting normally to the defaults and everything works fine, the only remaining problem is that the date and time are now reset after each system boot.
What Causes “Hyper Transport Flood Error”?
Sync Method 1: Clear/Replace CMOS Battery
If you find that the agreed date and time resets after each of these computers start up, the first suspect you usually think of is the CMOS battery. Fortunately, this small important component is located on the motherboard and is usually a CR2032 coin cell battery.
The Complementary Metal Oxide Semiconductor (CMOS) battery (also known as Oder rtc NVRAM) is responsible for storing information ranging from time to system hardware settings. The mismatch that this component is responsible for most often manifests itself in the inability toSave the date and time between launches.
If this scenario applies to your current scenario and you think you are dealing with an inaccurate CMOS battery, you should fix the problem quickly by either simplifying the CMOS battery or completely replacing this item if the problem persists.
Note. The following steps should be followed regardless of the configuration or windows brand of the PC.
- Completely turn off the laptop and make sure it is not connected in any way to the dominant outlet.
- Then remove the side panel and set the main hand stopper to inactive (if you have a wristband). By doing this, you ground the computer and the same power supply, ensuring you don’t damage your PC’s components.
- Look at your motherboard here and the CMOS battery ID. Intense should not be in place. Once you see the game, use your fingernail or a special non-conductive screwdriver to pry it out of the slot =”(max-width: 615px) 100vw, 615px” src=”https://cdn.Software IO.com/wp -content /uploads/ 2019/04/delete-cmos-battery.jpg” srcset=”https://cdn.Software IO.com/wp-content/uploads/2019/04/delete-cmos-battery.jpg 615w, https://cdn .Software IO.com/wp-content/uploads/2019/04/removing-cmos-battery-150×113.jpg 150W, https://cdn.Software IO.com/wp-content/uploads/2019/04/ remove- cmos-battery-300×227.jpg 300W”>
Removing the battery
Note cmos< /figcaption> If you have a multi-battery CMOS, replace the boot battery, make sure you don’t risk dealing with a bad battery.No, if you clean it thoroughly to make sure dirt doesn’t interfere with the connection to the motherboard.< /p>
- Wait a few minutes before repeating all steps and power on the new computer together.Then perform at least two consecutive reboots and see if the specific date and time are saved and you are still encountering the old “Hyper Transport Sync overflow error”. you
If you’ve done this, but you’re still getting a “Hyper Transport Sync Failed” torrent error every time you launch, move down to the next potential handle below.
Method 2: Disable Overclocking (if Applicable)
Similarly, timing avalanche occurs when high voltage train signals are in a state where normal operation is not possible. How are youPlease note that this problem can be caused by many hardware failures.
But in fact, in most cases, the use occurs when the BIOS has incorrectly configured the processor or chipset – probably due to overclocked clock speeds causing general system instability. It’s also possible that your non-PC can provide enough power due to overclocking.
Several affected users who also experienced this issue reported that the general issue was finally resolved after reducing the overclocking frequency of their CPU and GPU. For beginners, a factory reset may well help figure out if the overclocking issue is indeed a problem. Aria-scribeby=”caption-attachment-106616″>
One way to solve the problem without having to switch to a very powerful power supply is to remove all cool peripherals that are not necessary for the normal operation of your computer (non-critical PC peripherals, additional drives, hard optical drives). etc.). Also try lowering the current a bit if your GPU or CPU is overclocked and see if the problem goes away.Speed up your computer today with this quick and easy download.